Plywood Weight Calculator
A standard 1220 × 2440 mm plywood sheet weighs roughly 25 kg on a poplar core and roughly 36 kg on a birch core at 18 mm. The 11 kg difference comes entirely from core density, not from thickness. Imperial equivalent: a 3/4″ 4×8 sheet runs about 57 lb to 80 lb for the same reason. Enter your size, thickness and core below to get the exact figure for your order, along with consignment weight, CBM, and whether your load is weight-limited or volume-limited.
Calculate Plywood WeightPanel Details
Plywood Weight Calculator
Plywood Weight Calculator
Your Weight Results
How Much Does a Sheet of Plywood Weigh?
There is no single answer, and any source that gives you one number without naming a core is giving you an average. For a standard 4×8 sheet (32 sq ft) at 3/4″ nominal, expect roughly the following range. The spread is the honest answer, and the reason it spans 23 kg is density.
Nominal Is Not Actual
A sheet sold as 3/4″ typically measures about 23/32″, or 18.3 mm. A true 19 mm sheet weighs more than a nominal 18 mm one, and the two are routinely quoted interchangeably. Small percentages matter when you multiply them by a thousand sheets.
Face Veneer Barely Matters
On an 18 mm panel a 0.3 mm decorative face is under 2% of the total thickness. Weight is a core question. This surprises buyers who assume a heavier-looking figured face means a heavier panel.
Species Density Drives Weight
Softwoods like Douglas fir sit near 510 kg/m³ and Southern yellow pine near 560. Hardwoods run heavier: acacia around 610, eucalyptus around 650, birch around 670 to 680, hevea near 700.
Two Cautions Before You Plan
Use these figures for planning, not for a lift plan or a booking without confirmation. Nominal thickness differs from actual, and moisture content at shipment changes the final number.
Only a Weighed Panel Is Certain
Every figure here is a published industry value, labelled as such, and needs confirmation for your specific order. That is what a sample is for, and it is why we suggest ordering one before a first container rather than after.
Plywood Weight by Thickness
Weight scales directly with thickness once density is fixed. The table uses a 4×8 sheet (32 sq ft) and a metric 1220 × 2440 mm sheet. Treat every value as a working figure at 6–8% moisture content.
If you want the same data as a static table you can scan, print or download, we publish it separately as a full plywood sheet weight chart. Conversion note for mixed-unit jobs: 1 m² equals 10.764 sq ft.
6 mm (¼”)
Poplar ~19 lb / 9 kg · Softwood ~22 lb / 10 kg · Eucalyptus ~24 lb / 11 kg · Birch ~26 lb / 12 kg.
12 mm (½”)
Poplar ~38 lb / 17 kg · Softwood ~44 lb / 20 kg · Eucalyptus ~48 lb / 22 kg · Birch ~53 lb / 24 kg.
18 mm (¾”)
Poplar ~57 lb / 26 kg · Softwood ~67 lb / 30 kg · Eucalyptus ~71 lb / 32 kg · Birch ~80 lb / 36 kg.
25 mm (1″)
Poplar ~79 lb / 36 kg · Softwood ~93 lb / 42 kg · Eucalyptus ~99 lb / 45 kg · Birch ~110 lb / 50 kg.
Intermediate Thicknesses
9 mm (⅜”): Poplar ~28 lb / 13 kg · Softwood ~33 lb / 15 kg · Eucalyptus ~36 lb / 16 kg · Birch ~40 lb / 18 kg. 15 mm (⅝”): Poplar ~47 lb / 21 kg · Softwood ~56 lb / 25 kg · Eucalyptus ~60 lb / 27 kg · Birch ~66 lb / 30 kg. 21 mm (¹³⁄₁₆”): Poplar ~66 lb / 30 kg · Softwood ~78 lb / 35 kg · Eucalyptus ~83 lb / 38 kg · Birch ~93 lb / 42 kg.
The Variable That Decides Everything
Density is the mass of the wood in a given volume, expressed as kg/m³ or lb/ft³. It is a property of the species the core is made from, and it is the input that turns the same nominal panel into two very different weights. Your supplier’s data sheet takes precedence.
Typical Published Industry Values
The band on hardwood and meranti is wide on purpose. “Hardwood plywood” is a category, not a species, and the mills that fill it vary. If a quote says only “hardwood core”, ask for the species and the density before you plan a load against it.
~27 kg for an 18 mm 1220×2440 sheet. Light, stable, economical.
~31–33 kg. A durable mid-weight option with good surface hardness.
620–700 kg/m³ · ~33–38 kg. Category varies by mill; confirm species.
680–720 kg/m³ · ~37–39 kg. Dense core holds coating under load.
Lower density means lower consignment weight and easier handling.
A balance of weight, strength and cost for general construction.
Increased payload per sheet affects container load planning.
High density for strength and moisture resistance.
Approximate reference weights for an 18 mm, 1220 × 2440 mm panel. Actual weight varies by density, grade and manufacturer.
No standard hands you the number. Density is a specification value.
ANSI/HPVA HP-1-2024, which governs hardwood and decorative plywood, fixes face grades and construction but leaves panel weight and density to the manufacturer’s design. When a supplier cannot name the species behind a “hardwood core” quote, that is the answer you need to hear.
From Sheet Weight to Commercial Decision
This is where a sheet weight becomes a commercial decision. Multiply the per-sheet figure by your quantity, then add the packing. A pallet of 18 mm sheets at ~29.5 kg each, 50 sheets to a bundle, weighs about 1,475 kg before dunnage.
Volume capacity: ~33 CBM (20ft), ~67.7 CBM (40ft), ~76 CBM (40HC). Typical max payload: ~22 MT practical (20ft), ~26.7 MT (40ft), ~26.5–28.5 MT (40HC).
Which Constraint Binds First
Thin panels and light cores run out of volume first. Thick panels and dense cores run out of payload first. Two worked examples show why this matters: 18 mm eucalyptus at ~35 kg per sheet means 1,000 sheets weigh roughly 35 MT, exceeding a 40HC payload and needing two containers. 18 mm poplar at ~27 kg per sheet means a 40HC takes roughly 980 sheets at around 26.5 MT, sitting right at the payload ceiling.
Then add packing: pallets, edge protectors, straps and wrapping add roughly 20–30 kg per pallet. On an 18-pallet load that is a few hundred kilograms of packing that will appear on the weighbridge.
The same whether the core is poplar or birch. Two questions come from one order: how much does it weigh, and how much space does it take. Weight depends on species. Volume does not.
Choosing it by accident, without checking, is how the second container gets booked after the fact. Payload figures vary by carrier and by inland regulation, so treat these as typical and confirm the limit with your freight forwarder before you book.
Four Things Separate a Figure From a Weighbridge Ticket
A weight calculator gives you a figure you can plan with, not a figure you can invoice against. The only way to know a specific panel’s weight is to weigh it. That is what a sample is for.
Nominal vs Actual Thickness
A 3/4″ panel measures about 23/32″. Across a container, a few tenths of a millimetre either way is a few hundred kilograms.
Small percentages matter when you multiply them by a thousand sheets. Always confirm the actual thickness your supplier ships.
Moisture at Shipment
Mill-fresh panels carry more water than the 6–8% reference basis, and they lose it in transit.
Production weight and arrival weight are legitimately different numbers. Plan with the reference, confirm with the actual.
Glue Lines and Overlays
Present in the real panel, absent from most density tables. They add weight that no simple formula captures.
A calculated figure is a planning tool. The weighbridge ticket is the commercial document.
Mixed-Core Pallets
A container holding two core species cannot be estimated with an average density.
Mixed loads need separate calculations. The constraint that binds is the one set by the heavier core, not the average.
The only way to know a specific panel’s weight is to weigh it. That is what a sample is for, and it is why we suggest ordering one before a first container rather than after.
Panel Type Comparison by Density
If you are choosing between panel types rather than calculating one you have already specified, density is the comparison that matters. At equal thickness, from lightest to heaviest.
Softwood Plywood
~520 kg/m³. Baseline for comparison. A 3/4″ 4×8 sheet weighs roughly 65 lb. Lightest common plywood option.
Hardwood Plywood
620–700 kg/m³. 20–35% heavier than softwood plywood. Species category varies; confirm density with your supplier.
OSB
~640–657 kg/m³. Heavier than softwood plywood at equal thickness. A 3/4″ 4×8 sheet weighs around 76 lb.
Particle Board
~640 kg/m³. Comparable to OSB. A common economical core for decorative panels where weight is not the primary constraint.
MDF
~740 kg/m³. The heaviest common sheet material. A 3/4″ 4×8 sheet weighs about 95 lb. Dense, uniform, and flat.
Frequently Asked Questions
Practical answers about plywood sheet weight, core density, thickness, pallet loads and container capacity.
A 3/4″ 4×8 sheet weighs roughly 57 lb on a poplar core, 67 lb on softwood, 71 lb on eucalyptus and 80 lb on birch. The 23 lb spread is core density, not thickness. At 1/2″ the same sheet runs about 38 to 53 lb.
A 1220 × 2440 mm sheet at 18 mm weighs roughly 25–27 kg on poplar, 28 kg on softwood or pine, 31–33 kg on acacia, 35 kg on eucalyptus and 36–39 kg on birch. The volume is a constant 0.0536 m³, so density is the only variable.
Not exactly. 3/4″ nominal is 19.05 mm, and the sheet you receive typically measures about 23/32″ or 18.3 mm. An 18 mm metric sheet and a nominal 3/4″ sheet are close enough to interchange in most applications but not identical, and not identical in weight either.
It depends on the core and the pallet count. Around 50 sheets of 18 mm at ~29.5 kg each is roughly 1,475 kg before dunnage, and pallets, edge protection, straps and wrapping add roughly 20–30 kg per pallet. Always ask for the packed weight, not the net weight.
Yes. Panels at mill-fresh moisture content of 10–18% weigh 10–20% more than the same panel at the 6–8% dry-shop reference basis. Pressure-treated plywood can be 30–50% heavier immediately after treatment. The weight falls again as the panel dries.
Roughly 980 sheets on a light poplar core at about 27 kg, falling to around 750 sheets on eucalyptus at about 35 kg. A 40HC is weight-limited at 18 mm, not volume-limited, so the answer depends on the core rather than the box. Use the calculator for your specific core and confirm the payload with your forwarder.
Poplar and styrax, at roughly 450–520 kg/m³. Birch and film-faced panels are heaviest at 680–720 kg/m³. If you are optimising a load, a lighter core is the single biggest lever available: worth checking before you assume you need a second container.