LENGTH CONVERSION TOOL

Edge Banding Meters to Feet Converter

To convert edge banding meters to feet, multiply the meters by 3.28084. A 100-meter roll of edge banding is 328 feet, and a 200-meter roll is 656 feet.

Edge banding is sold by the roll in meters almost everywhere in the world, so if your shop works in feet and inches — or you are reading a supplier quote written in the other system — this converter gives you the number in the units you actually use, in both directions.

Convert Edge Banding Length
Length Conversion 200 m → 656 ft

Edge Banding Roll

Meters 200 m
Feet 656 ft
Inches 7,874 in
Millimeters 200,000 mm
EDGE BANDING LENGTH CONVERTER

Convert Edge Banding Length in Four Units

Enter any single length and the converter returns the equivalent in meters, feet, inches and millimeters. Roll length is quoted in meters while banding width is quoted in millimeters — this tool removes the conversion step.

01 Enter Length
02 Meters
03 Feet
04 Inches
05 Millimeters
06 Roll Length
07 Rolls Needed

Length Converter

Converted Length

Meters 200 m
Feet 656 ft
Inches 7,874 in
Millimeters 200,000 mm
Roll length is quoted in meters and banding width in millimeters even by suppliers selling into the United States. The imperial figure is a conversion the buyer performs — which is what this page is for.
01 — CONVERSION BASICS

Convert edge banding meters to feet

The conversion is a fixed number, not an estimate. One meter is defined as exactly 3.28084 feet, which means the calculation never changes and never depends on the material.

Meters to Feet × 3.28084
Feet to Meters × 0.3048
Millimeters to Feet ÷ 304.8
Millimeters to Inches ÷ 25.4
Inches to Millimeters × 25.4
01

Meters to Feet

Multiply the number of meters by 3.28084. A 200-meter roll of PVC edge banding is 200 × 3.28084 = 656 feet. This is the conversion that comes up most often, because roll length is quoted in meters while most US and UK workshops plan cutting in feet.

02

Feet to Meters

Multiply by 0.3048 to go the other way. A 250-foot run is 250 × 0.3048 = 76.2 meters, and a 26.4-meter cabinet job is 26.4 × 3.28084 = 86.6 feet. The number changes, the buying decision does not.

03

Millimeters to Inches

Divide the millimeters by 25.4. A 22 mm banding strip is 22 ÷ 25.4 = 0.87 inches, just under 7/8 inch. This is the standard banding width for an 18 mm panel, so the conversion is worth knowing by heart.

04

The Two Conversions That Matter Most

Roll length is quoted in meters and banding width is quoted in millimeters — even by suppliers selling into the United States. Those are the two figures that decide what you order, and those are the two conversions this page removes.

05

Why Edge Banding Is Metric-First

Edge banding is a manufactured roll good, and the metric system is the global standard for panel products. A roll of a given thickness holds a predictable number of meters, so every factory measures the strip in meters and leaves the imperial figure to the buyer.

THE BASIC RULE The conversion is mechanical, not judgment — a fixed factor applied to a length.
02 — QUICK REFERENCE

Edge banding conversion table

Use this table when you are reading a quote or a spec sheet and want the number without opening a calculator.

Edge banding value
Meters
Feet
Millimeters
Inches
50 m roll
50
164
50,000
1,969
100 m roll
100
328
100,000
3,937
200 m roll
200
656
200,000
7,874
300 m roll
300
984
300,000
11,811
500 m roll
500
1,640
500,000
19,685
16 mm width
0.016
0.052
16
0.63
18 mm width
0.018
0.059
18
0.71
22 mm width
0.022
0.072
22
0.87
25 mm width
0.025
0.082
25
0.98
1.0 mm thickness
0.001
0.003
1.0
0.039

Feet are rounded to the nearest whole foot and inches to the nearest hundredth; the converter above gives the exact figure.

03 — WHY METERS

Why edge banding is quoted in meters, and when you need feet

Edge banding starts as a continuous strip wound onto a core, and every factory measures that strip in meters because a roll of a given thickness holds a predictable number of meters. Thinner banding builds a longer roll; thicker banding builds a shorter one — roughly 200 meters for 0.4–1.0 mm banding, 100 meters for 1.0–2.0 mm, and 50 meters for 2.0–3.0 mm.

A US or UK workshop

Ordering from a metric supplier and needing to plan cutting in feet and inches.

An importer or distributor

Comparing two quotes, one written in meters and one in feet, and wanting them on the same basis.

A furniture or cabinet manufacturer

Reading a panel specification in millimeters and translating it to the imperial stock they already cut.

04 — ROLL LENGTHS

Edge banding roll lengths in meters and feet

Roll length is the first number a buyer sees on a quote, so it is worth having the imperial equivalents to hand.

Roll length
50 m
100 m
200 m
300 m
500 m
Roll length (feet)
164 ft
328 ft
656 ft
984 ft
1,640 ft
Typical thickness
2.0–3.0 mm
1.0–2.0 mm
0.4–1.0 mm
0.4–0.8 mm
Custom / thin

Pre-glued banding is commonly packed at 100 or 200 meters. If a standard roll does not divide cleanly into your project, ask about a custom roll length — Vital Wood Global cuts rolls to order rather than forcing fixed multiples.

05 — WIDTH & THICKNESS

Banding width and thickness in millimeters and inches

Width is the second number on the quote, and it is nearly always given in millimeters. Matching it to an imperial panel is where a small conversion error causes a real problem, because banding should be slightly wider than the panel so a small overhang trims flush on both faces.

Panel thickness
Banding width (mm)
Banding width (in)
Banding thickness (mm)
18 mm (≈ 3/4 in)
20–23 mm
0.79–0.91 in
1.0–1.5 mm
25 mm (≈ 1 in)
28–32 mm
1.10–1.26 in
1.5–2.0 mm
12 mm (≈ 1/2 in)
16–18 mm
0.63–0.71 in
0.5–1.0 mm

A 22 mm strip (0.87 in, about 7/8 in) is the standard choice for an 18 mm panel. Ordering an exact-width 18 mm band has no trimming allowance and tends to show glue lines, so the extra millimeter or two is deliberate.

06 — FROM CONVERSION TO QUANTITY

From conversion to quantity

Converting units is only the first step. The number you actually order depends on how much banding your project consumes, and that is a separate calculation.

01

Total Exposed Edge Length

Everything starts with the edges that actually get banded.

COUNT Exposed edges only
UNIT Meters or feet
BASIS Panel perimeter

Add up the edges that will receive banding — not every edge of every panel. The total becomes the raw quantity that everything else builds on.

02

Panel Count

How many panels — and how many banded edges on each — drives the total.

COUNT Panels per unit
VARIATION Edges per panel
IMPACT Total length

A run of cabinets where only the fronts are banded consumes far less than one where every carcass edge is finished. Count the edges, not just the panels.

03

Waste Allowance

Cutting and matching affect yield, so the allowance belongs in the specification.

PRIORITY Cutting waste
TYPICAL 10–20%
PURPOSE Avoid shortfalls

Book matching and decorative patterns consume more than a plain slip match. Accounting for that during specification prevents shortages without unnecessary over-ordering.

04

Rolls Needed

Total length divided by standard roll length gives the order quantity.

PRIORITY Match standard rolls
TOOL Edge banding calculator
RESULT Order quantity

Enter your panel length and width, the number of panels, and which edges get banded, and the calculator returns the total in meters or feet, the rolls needed, and the right width and thickness for the panel.

NEXT STEP

Convert, then order the right length

Convert the roll length and banding width into the units you need, then send the result over and we will come back with factory-direct pricing, stock availability, and lead time for the exact banding you specified.

Frequently asked questions

Practical answers about edge banding conversion, roll lengths, banding width and the quantity you actually need to order.

Multiply the number of meters by 3.28084. A 200-meter roll is 200 × 3.28084 = 656 feet. To convert feet back to meters, multiply by 0.3048.

328 feet. A 100-meter roll is the standard pack for 1.0–2.0 mm banding, and 328 feet is the exact equivalent.

0.87 inches, just under 7/8 inch. Divide millimeters by 25.4 to convert — 22 ÷ 25.4 = 0.87. This is the standard banding width for an 18 mm (3/4 in) panel.

76.2 meters. Multiply feet by 0.3048, so 250 × 0.3048 = 76.2 meters.

Meters, almost universally. Roll length is quoted in meters and banding width in millimeters even by suppliers selling into the United States. The imperial figure is a conversion the buyer performs, which is what this page is for.

Divide the millimeters by 25.4. A 1.0 mm band is 0.039 inches, and a 2.0 mm band is 0.079 inches. This is useful when matching banding thickness to an imperial panel.